FPQ6 MPC8313E implementation

This course covers PowerQUICC II Pro MPC8313


Objectives
	The course focuses on the sequencer that interconnects e300, DDR SDRAM, PCI and external bus.
	Cache coherency protocol is introduced in increasing depth.
	The 32-bit e300 core is viewed in detail, especially the MMU and the cache.
	The boot sequence and the clocking are explained.
	The course focuses on hardware implementation of the MPC8313E.
	A long introduction to DDR SDRAM operation is done before studying the DDR2 SDRAM controller.
	An in-depth description of the PCI controllers is performed.
	The course highlights both hardware and software implementation of gigabit / fast / Ethernet controllers.
	The USB interfaces are also detailed.
	Generation of a Linux image and Root File System by using LTIB can also be included into the training.
A lot of programming examples have been developed by ACSYS to explain the boot sequence and the operation of complex peripherals, such as USB and Ethernet. •They have been developed with Diab Data compiler and are executed under Lauterbach debugger.
A more detailed course description is available on request at info@ac6-training.com


Prerequisites and related courses
	The knowledge of the following interconnect standards may be required:
		PCI, see our course reference IC1
		Gigabit Ethernet, see our course reference N1
		USB 2.0, see our course reference IP2

Outline


INTRODUCTION TO MPC8313E
Overview
	Enhancements compared to MPC824X
	Memory map
	Block diagram
	Application examples
THE e300 CORE
THE INSTRUCTION PIPELINE
	Pipeline
	Branch processing unit
	Simplified branch mnemonics
	Coding guidelines
DATA PATHS
	Load / store buffers
	Sync and eieio instructions
	Store gathering mechanism
CACHES
	Cache basics
	Relationship between cache and burst, critical word first order
	L1 caches
	Shared resource management
	Cache coherency mechanism
	Management of cache enabled pages shared with PCI DMAs
	Cache related instructions
	Cache flush routine
SOFTWARE IMPLEMENTATION
	PowerPC architecture specification, the 3 books UISA, VEA and OEA
	Addressing modes, load / store instructions
	Integer instructions
	Rotate instructions : inserting and extracting bitfields
	IEEE754 basics, floating points numbers encoding
	Floating point arithmetical instructions
	The PowerPC EABI
	Linking an application with Diab Data, parameterizing the linker command file
THE MMU
	Thread vs process
	Introduction to real mode, block and segmentation / pagination translations
	Real mode restrictions
	Memory attributes and access rights definition
	Virtual space benefit, page protection through segmentation
	TLBs organization
	PTE table organization, tablesearch algorithm
	MMU implementation in real-time sensitive applications
THE EXCEPTION MECHANISM
	Save / restore registers SRR0/SRR1, rfi instruction
	Exception management mechanism
	Registers updating according to the exception cause
	Requirements to allow exception nesting
THE DEBUG PORT
	JTAG emulation, restrictions
	Code instrumentation
	Hardware breakpoints
THE PLATFORM CONFIGURATION
POWER, RESET AND CLOCKING
	DC and AC electrical characteristics
	Reset causes
	Configuration signals sampled at reset
	Reset configuration words source, boot from I2C or boot from EEPROM
	PCI Host / Agent configuration
	Clocking in PCI Host mode, system clock domains
	System PLL ratio
	Delay Locked Loop
ADDRESS TRANSLATION AND MAPPING
	Local memory map
	Local access windows
	Distinguishing Local Access Windows from other mapping functions
	Inbound and outbound windows definition
ARBITER AND BUS MONITOR
	External signal description
	PCI outbound window definition
	Transaction forwarding
SEQUENCER
	Coherent system bus overview
	Arbitration policy
	Bus error detection
GENERAL PURPOSE INPUTS / OUTPUTS
	Pin model
	Interrupt inputs
THE DDR2 MEMORY CONTROLLER
	DDR-SDRAM operation : a 128-Mbits DDR-SDRAM from Micron is used as an example
	Jedec specification basics
	Differences between DDR1 and DDR2
	Command truth table
	Refresh types
	Bank activation, read, write and precharge timing diagrams, page mode
	ECC error correction
	DDR-SDRAM controller overview
	Initial configuration following Power-on-Reset
	Address decode
	Timing parameters programming
	Initialization routine
LOCAL BUS CONTROLLER
	Multiplexed or non-multiplexed address and data buses
	Dynamic bus sizing
	GPCM, UPMs states machines
	Interfacing to ZBT SRAMs
	Interfacing to DSP host ports
	NAND flash controller
PCI BUS INTERFACE
	Bridge features
	Data flows : Read prefetch and write posting FIFOs
	Inbound transactions handling, Outbound transactions handling
	PCI bus arbitration
	PCI hierarchy configuration when operating as host
INTEGRATED DMA CONTROLLER
	Priority between the 4 channels
	Support for cascading descriptor chains
	Concurrent execution across multiple channels with programmable bandwidth control
	Messaging unit
	Doorbells management
INTEGRATED PROGRAMMABLE INTERRUPT CONTROLLER
	Interrupt masking
	Definition of interrupt priorities
	System critical interrupt
	Requirements to support nesting
TIMERS
	Software watchdog timer
	Real time clock module
	Periodic Interval Timer
	General Purpose Timers
INTEGRATED PERIPHERALS
SECURITY ENGINE [optional, MPC8313E only]
	Overview of the encryption mechanism
	Introduction to DES and 3DES algorithms
	Data packet descriptors
	Crypto channels
THE ETHERNET CONTROLLERS
	802.3 specification fundamentals
	MAC address recognition, 256-entry hash table for unicast and multicast
	Interface with the PHY (SGMII)
	Buffer descriptors management
	Flow control
	Level 2, 3 and 4 hardware acceleration mechanisms (TCP/IP Offload Engine)
	Quality of service support
	Hardware assist for IEEE1588 support
THE USB 2.0 CONTROLLER
	Dual-role (DR) operation
	EHCI implementation
	UTMI / ULPI interfaces to the transceiver
	OTG support
	Dedicated DMA channels
	Endpoints configuration
LOW SPEED PERIPHERALS
	Description of the NS€50/16550 compliant Uarts
	Flow control signal management
	I2C protocol fundamentals
	Transmit and receive sequence
	SPI protocol basics
	Master vs slave operation
Linux Target Image Builder (LTIB)
GENERATING THE LINUX KERNEL IMAGE
	Introducing the tools required to generate the kernel image
	What is required on the host before installing LTIB
	Common package selection screen
	Common target system configuration screen
	Building a complete BSP with the default configurations
	Creating a Root Filesystems image
	e-configuring the kernel under LTIB
	Selecting user-space packages
	Setup the bootloader arguments to use the exported RFS
	Debugging Uboot and the kernel by using Trace32
	Command line options
	Adding a new package
	Other deployment methods
	Creating a new package and integrating it into LTIB
		A lot of labs have been created to explain the usage of LTIB

Duration	Cost	Calendar
5 days	2100 €